Presence detector for ceiling mounting indoors. The sensor module detects moving heat sources (e.g. people) in an adjustable detection range and starts a staircase lighting time. For ohmic, inductive and capacitive loads such as incandescent lamps, energy-saving lamps, low-voltage halogen lighting with conventional transformers, electronic transformers, fluorescent lamps. The sensor module has a light sensor with an adjustable brightness threshold so that the lighting is only switched on below a certain brightness threshold. The presence function enables the sensor module to switch the lighting off even if a person is present if there is sufficient natural light. For installation in a 60 mm flush-mounted box or in the surface-mounted housing available as an accessory. With claw and screw fastening. With screw terminals. Functions: -Switching from one output. External control via a PL input (sensor module on central unit insert (slave), extension unit plus). Switching. Brightness-dependent staircase lighting function. Nominal voltage: AC 220/230 V, 50/60 Hz. Nominal current: max. 10 AX, cos Phi 0.6. Outputs: 1x normally open contact. Max. switching capacity per channel: Incandescent lamps: 2200 W. HV halogen lamps: 2000 W. LV halogen lamps with wound transformer: 500 VA. Electronic transformers: 1050 W. Capacitive load: 10 A, 140 uF. Energy saving lamps: 100 VA. Motor load: 1000 VA. Neutral conductor: required (3 conductor system). Connection cross-section: max. 2x2.5 mm. Detection angle: 360 degrees. Number of levels: 6. Number of zones: 136. Number of motion sensors: 4. Recommended installation height: 2.5 m. Range: max. radius of 7 m (at an installation height of 2.50 m). Sensitivity: continuously adjustable. Brightness threshold: continuously adjustable from approx. 10 to approx. 1000 lux. Follow-up time: Channel 1: continuously adjustable from approx. 10 s to approx. 30 min. Color: polar white.
| Property | Value |
| Max. Range to one side: | 7 m |
| Optimal installation height: | 2.5 m |
| Design: | Presence detector |
| Color: | white |
| Mounting type: | Flush-mounted |
| Response brightness: | 1000 lx |
| Protection class (IP): | IP20 |
| Max. Switching capacity: | 2200 W |
| Max. Inrush current: | 10 A |
| Nominal voltage: | 230 V |
| Sensor type: | passive infrared |
| Voltage type: | AC |
| Surface finish: | glossy |
| Material: | plastic |
| Surface: | untreated |
| Material quality: | thermoplastic |
| Max. Frontal range: | 7 m |
| Detection field diameter on floor: | 14 m |
| Min. duty cycle: | 10 s |
| Max. Duty cycle: | 30 min |
| Number of switching zones: | 136 |
| Switch-off delay: | 1800 s |
| RAL number (similar): | 9010 |
| Horizontal detection angle: | 360 ° |
| Frequency: | 60 Hz |
| Halogen-free: | yes |
| Adjustable response brightness: | yes |
| Creep protection/rear field monitoring: | yes |
| Constant light control: | no |
| HVAC control: | no |
| Forced shutdown: | no |
| Animal corridor: | no |
| Networkable: | yes |
| Staircase monitoring: | yes |
| Bypass switch: | no |
| Suitable for wireless transmission: | no |
| Remote controllable: | yes |
| Response sensitivity adjustable: | yes |
| With signal unit: | no |
| Alarm function: | no |
| Teach function for response brightness: | no |
| Dimming function with dimming insert: | no |
| Transparent: | no |
| With remote control: | no |
| Suitable for C load: | no |
| With DALI interface: | no |
| Extension input: | yes |
| Forced switching on: | no |
| Scan angle: | 360 ° |
| Max. Presence range: | 113 m |
| Suitable for ceiling mounting: | yes |
| Suitable for wall mounting: | no |
| Connection type: | screw terminal |
| Antibacterial treatment: | no |
| Width: | 116 mm |
| Height: | 116 mm |
| Depth: | 72 mm |
| Diameter: | 116 mm |
| Installation width: | 60 mm |
| Installation depth: | 30 mm |
| Installation length: | 60 mm |
| Installation diameter: | 60 mm |
| Min. depth of device box: | 46 mm |
