+351 934 234 451‬
Rua Bartolomeo Dias 20, 8200-096 Albufeira, Portugal
Catalog
All categories
  • All categories
  • Smart home systems
  • Home and Garden
  • Electrics
  • Installation
  • Lamps and lights
  • Lamps and luminaires
  • PV systems and accessories
  • Other ranges
  • Accessories and Appliances
Catalog

Eltako 28380512 DSZ15DM-3x80A MID calibrated M-Bus three-phase meter

Brand:Eltako
To compare
To favorites
SKU:405961
Eltako 28380512 DSZ15DM-3x80A MID calibrated M-Bus three-phase meter
Maximum current (Imax)
Accuracy class
HAB
Manufacturer
In stock
€194.32
11
Shipping information
International shipping DHL
Рассчитываем стоимость доставки...
DPD
Рассчитываем стоимость доставки...
UPS
Рассчитываем стоимость доставки...
Description
Features
Reviews

Only calibrated meters are permitted for electricity billing according to paragraph 25 of the German Calibration Act. Failure to comply is an administrative offence according to paragraph 19. M-Bus three-phase meter. Maximum current 3x80A, standby loss only 0.5 watts per path. Series-mounted device for mounting on DIN-EN 60715 TH35 mounting rail. 4 division units = 70mm wide, 58mm deep. Accuracy class B (1%). With M-Bus interface. The direct-measuring three-phase meter measures the active energy based on the currents flowing between the inputs and outputs. The internal consumption of only a maximum of 0.5 watts of active power per path is not measured and is not displayed. 1, 2 or 3 external conductors with currents of up to 80A can be connected. The starting current is 4OmA. The N connection must be present. The 7-segment LC display can be read twice within two weeks even without a power supply. The power consumption is displayed with an LED that flashes 1000 times per kWh. Can also be used as a 2-tariff meter as standard: Applying 230V to terminals E1/E2 switches to a second tariff. To the right of the display are the MODE and SELECT buttons, which are used to scroll through the menu according to the operating instructions. First, the background lighting switches on. Then the total active energy per tariff, the active energy of the resettable memory RS1 or RS2 and the instantaneous values of power, voltage and current per outer conductor can be displayed. Error message (false): If an outer conductor is missing or the current direction is incorrect, false and the corresponding outer conductor are shown in the display. M-Bus data transfer: When reading out, all values are transmitted in one telegram. The following telegrams are supported: Initialization: SNDNKE, response: ACK, read meter: REQUD2, response: RSPUD, change primary address: SNDUD, response: ACK, reset RS1: SNDUD, response: ACK, slave selection for the secondary address, response: ACK. The device does not respond to unknown queries. The transmission rate is automatically detected. The device has a voltage monitor. In the event of a voltage loss, all registers are saved in the EEPROM. Changing the M-Bus primary address: To change the M-Bus primary address, hold down SELECT for 3 seconds. In the following menu, MODE increases the address by 10, SELECT increases it by 1. When the desired primary address is set, wait until the main menu appears again. Secondary address: Using the secondary address, it is possible to communicate with the energy meter in accordance with the EN13757 standard. Wild cards can be used. Detailed information can be found in the operating instructions at www.eltako.com.

Property Value
Width in division units: 4
Calibrated: yes
Pole type: Four-wire
Meter type: electronic
Display type: digital
Mounting type: REG
Accuracy class: B
Maximum current (Imax): 80 A
Nominal voltage (Un) NL: 230 V
Protection class (IP): IP20
Frequency: 50 Hz
Tariff version: Two-tariff
Tariff control: external
Energy type: Active power
Nominal current (In): 10 A
Design: Direct measurement
Nominal voltage (Un) LL: 400 V
Number of digits: 7
Suitable for: Reference
Backstop: yes
Approval: Measuring Instruments Directive
Interface design: M-Bus
Features
Maximum current (Imax)
Accuracy class
HAB
Manufacturer
HAN
GTIN
Version
Implementation of the interface
Width in pitch units
Frequency
Suitable for
Mounting type
Nominal current (In)
IP protection)
Permit
No reviews yet — your comment may be first.
All reviews 0
general rating
Related Products