Eltako 30000022 Blister pack dimming BPD-OE FT55R-alpine white + FUD61NPN-230V

Blister pack dimming consists of a battery- and wire-free radio button FT55R in alpine white (without frame) for Busch Reflex and Duro cover frames and a universal dimming actuator FUD61NPN-230V. The dimmer automatically detects the lamp type and enables the minimum brightness and dimming speed to be set. FT55R-alpine white: Radio button FT55R in alpine white for frame internal dimensions 55x55mm with radius, 15mm high. Generates the energy for radio telegrams itself when the button is pressed, therefore no connection cable and no standby loss. For Busch Reflex and Duro cover frames. The scope of delivery includes a rocker, a double rocker, a mounting frame, a holding plate (all the same color), the radio module and an adhesive film. Radio buttons with a rocker can send two evaluable signals: press the rocker up and press the rocker down. Radio buttons with double rockers can send four evaluable signals: Press two rockers at the top and bottom. The mounting plate can be screwed onto a flat surface or stuck to the wall, glass or furniture using the adhesive film provided. The sleeves in the box are used for screw fastening over a 55mm switch box. The radio button lighting FTB can then also be snapped onto the mounting plate from behind. The double rocker is snapped onto the radio module as standard. If you want to replace this with the large rocker, pull the rocker halves forwards and do not bend them towards the middle. Then snap the large rocker onto the plate so that the markings 0 and I on the back match the radio module. When gluing, first glue the mounting plate set with frame and fastening frame - with the notches at the top and bottom. Then snap the radio module set with rocker - marking 0 on the back always at the top - into place. Before screwing, remove the frame with fastening frame from the mounting plate. To do this, press the catches on the holding plate outwards. Then screw on the holding plate - with the catches at the top and bottom -, snap on the frame with the fastening frame and snap in the radio module set with rocker switch - marking 0 on the back always at the top. For screw fastening, we recommend sheet metal countersunk screws 2.9x25mm, DIN 7982 C. Both with dowels 5x25mm and on 55mm switch boxes. FUD61NPN: Universal dimmer switch, power MOSFET up to 300W. Automatic lamp detection. Standby loss only 0.7 watts. Minimum brightness or dimming speed adjustable. With children's room, snooze and light alarm switch. Also with light scene control. Encrypted radio, bidirectional radio and repeater function can be switched on. For recessed installation. 45mm long, 45mm wide, 33mm deep. Universal dimmer switch for lamps up to 300W, depending on the ventilation conditions. Dimmable energy saving lamps ESL and dimmable 230V LED lamps also dependent on the lamp electronics. Zero-crossing switching with soft on and soft off to protect the lamp. Local supply, switching and control voltage 230V. No minimum load required. This dimmer switch is controlled using the FT and FFT radio buttons, the FHS and FMH radio hand-held transmitters and the FF8 and UFB remote controls. The set brightness level is saved when switched off (memory). In the event of a power failure, the switch position and brightness level are saved and switched on when the supply voltage returns, if necessary. Automatic electronic overload protection and overtemperature shutdown. From production week 11/14, encrypted sensors can be taught in. Bidirectional radio and/or a repeater function can be switched on. Every change of status and incoming central control telegrams are then confirmed with a radio telegram. This radio telegram can be programmed into other actuators such as the FSR61NP-230V, the GFVS software and universal displays. The GFVS software also displays the current dimming value in %. The upper % lamp/dim speed rotary switch can be used to set either the minimum brightness (fully dimmed) or the dimming speed. The lower rotary switch determines during operation whether automatic lamp detection should be activated or special comfort positions: AUTO allows all types of lamps to be dimmed. EC1 is a comfort position for energy-saving lamps which, due to their design, must be switched on with a higher voltage so that they can be safely switched on again when dimmed, even when cold. EC2 is a comfort position for energy-saving lamps which, due to their design, cannot be switched on again when dimmed. Memory is therefore switched off in this position. LC1 is a comfort position for LED lamps which, due to their design, cannot be dimmed far enough on AUTO (trailing edge phase control) and therefore have to be forced to leading edge phase control. LC2 and LC3 are comfort positions for LED lamps like LC1, but with different dimming curves. Inductive (wound) transformers must not be used in the EC1, EC2, LC1, LC2 and LC3 positions. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO position due to the design. The buttons can be programmed either as directional buttons or as universal buttons: As a directional button, one side can be switched on and dimmed up, and the other side can be switched off and dimmed down. A double click on the switch-on side triggers automatic dimming up to full brightness at dim-speed. A double click on the switch-off side triggers the snooze function. The children's room switch is carried out on the switch-on side. As a universal button, the direction is reversed by briefly releasing the button. Light scene control, light alarm function, children's room function and snooze function according to the operating instructions. The LED accompanies the learning process in accordance with the operating instructions and indicates radio control commands during operation by flashing briefly.