LED universal dimming station 4-way REG housing 8 TE
Intended use
Switching and dimming of incandescent lamps, HV halogen lamps, dimmable HV LED lamps, dimmable compact fluorescent lamps, dimmable inductive transformers with LV halogen or LV LED lamps, dimmable electronic transformers with LV halogen or LV LED lamps
Suitable for mixed loads up to the specified total power
No mixed load operation of electronic and inductive transformers on the same load output
Operation using sensor modules, touch sensor modules, 24 V touch sensors, 24 V touch sensor modules or non-illuminated installation buttons
Installation on top hat rail according to DIN EN 60715 in sub-distribution board
Operation of the device with universal power additives in combination with electronic transformers is not possible! To increase the power when operating electronic transformers, use Tronic power boosters.
Product features
Keypad for operating the dimming station
Control of feedback LEDs at the control points. The dimming station has control outputs A1' ... A4' for this purpose.
Electronic short-circuit protection with permanent shutdown after 7 seconds at the latest
Electronic overtemperature protection
Switch-on brightness can be set separately for each load output
Switch-on brightness can be saved permanently
Switch-on using a lamp-friendly soft start
Switch-off using a dimming function
Output power can be increased by connecting several outputs in parallel
Power can be expanded using power add-ons (item no. ULZ 1755 REG)
Connection for hotel card switch
Central function Central ON, Central OFF: Switching the load outputs on or off together
Parallel connection of two dimming stations or one dimming station and one relay station
Automatic setting of the dimming principle that suits the load
Optional accessories: LED compensation module, item no.: KM LED 230 U
Hotel card switch function
In combination with a hotel card switch (item no.: .. CARD ..), the light is switched on to the switch-on brightness after the hotel card is inserted. After the hotel card is removed, the light remains switched on for approx. 1 minute and the dimming station can be operated. After the time has elapsed, the light is dimmed to the minimum brightness within an adjustable time of approx. 30 seconds - 3 minutes and then switched off. The dimming station can only be operated again after the hotel card has been inserted.
Nominal voltage: AC 230/240 V ~, 50/60 Hz
Power loss: max. 20 W
Standby power: max. 2 W
Terminals -, +
Control voltage: DC 24 V SELV
Current load capacity: 80 mA
Length of control cable: max. 100 m
Number of control points
Sensor module (item no.: SM 1608): max. 4 (also for relay/dimming stations connected in parallel)
Touch sensor module (item no.: 4008 TSM): max. 4 (also for relay/dimming stations connected in parallel)
Touch sensor modules 24 V AC/DC (normally open): depends on the touch sensor module, note the current consumption
Switching inputs E1ON/OFF ... E4ON/OFF
Control voltage: DC 24 V SELV
Resistance Ri: 200 k
Control outputs A1' ... A4'
Control voltage: DC 24 V SELV
Current carrying capacity: 10 mA
Resistance Ra: 330
Mains / load outputs / hotel card switch
Connection type: screw terminals
single-wire: 1 x 1.5 ... 4 mm2
fine-wire without wire end ferrule: 1 x 0.75 ... 4 mm2
fine-wire with wire end ferrule: 1 x 0.5 ... 2.5 mm2
Connection switching inputs / control outputs / control points
Connection type: screw terminals
single-wire: 1.5 mm²
fine-wire without Wire end ferrule: 1 mm²
fine-stranded with wire end ferrule: 0.75 mm²
Load outputs A1 ... A4
Contact type:
Length of load cable per channel: max. 100 m
Connected load per channel
Incandescent lamps: 20 ... 150 W
HV halogen lamps: 20 ... 150 W
Electronic transformers: 20 ... 150 W
Inductive transformers: 20 ... 150 VA
HV LED lamps dimmable: typically 3 ... 30 W
Compact fluorescent lamps dimmable: typically 3 ... 30 W
Ohmic-capacitive: 20 ... 150 W
Ohmic-inductive: 20 ... 150 VA
Capacitive-inductive: not permitted
Power reduction for every 5 °C exceeding 45 °C: -15 %
Load outputs connected in parallel may only be used to 80 % capacity.
Installation width: 144 mm (8 HP)
| Property | Value |
| Width in modular units: | 8 |
| Mounting type: | REG |
| Number of outputs: | 4 |
| Output power: | 150 W |
| Voltage: | 240 V |
| Frequency: | 60 Hz |
| Design: | Control module |
| Load type: | universal |
| Power supplement usable: | no |
| KNX bus system: | no |
| Radio bus system: | no |
| Powernet bus system: | no |
| With bus connection: | yes |
| LON bus system: | no |
| Other bus systems: | without |
| Extension input: | no |
| Local/manual operation: | yes |
| With LED display: | yes |
| Max. Control current: | 80 mA |
| Parallel operation possible: | yes |
| KNX radio bus system: | no |
| Removable bus module: | no |
| Bidirectional radio: | no |
